switch n. 1.(樹上折下的)細樹枝;軟鞭子;鞭打。 2.假發;(尾巴上的)毛簇。 3.〔美國〕【鐵道】道岔扳子,軌閘轉轍器;側線。 4.【電學】開關;電閘;電鍵;轉換器;【電話】接線臺。 5.【軍事】斜行壕。 6.(思想等的)大轉變。 7.〔美國〕(金融機構和銷售店的)電腦化聯網。 a change-over switch 轉換開關,轉向開關。 a pull switch 拉線開關。 a three wire switch 雙聯開關。 a time switch 定時斷路器。 a clock switch 定時開關。 a line switch (自動電話的)尋線機,預選器;線路開關。 vt. 1.鞭打;擺動;搖(尾);猛然搶去。 2.掛斷(…的電話)(switch sb. off);關閉(電流),關(電燈) (off; out)。 3.通(電流),接通(電話給某人),開(電燈) (on)。 4.改變,轉變(思想、談話等);【鐵道】給扳道岔;調配(車廂)。 vi. 1.鞭打。 2.【鐵道】扳道岔;調車。 3.掛斷電話 (off)。 4.轉換,轉變。 switch an electric light on [off] 開[關]燈。 switch off to another like of thought 改變想法[思路]。 Let's switch. 〔美國〕走吧;開動吧。 I'll be switched. 〔美口〕〔表示否定、驚訝〕(I'll be switched if you do. 你要是能的話我就把頭砍掉)。 switch off [on] 不收聽[收聽](某一廣播)。 switch through 【電信】轉接。
Analysis and simulation of simultaneous switching noise for cmos ic 電路同步開關噪聲的分析和仿真
Analysis and suppression of simultaneous switching noise in high-speed chip package 高速芯片封裝結構的同步開關噪聲分析及抑制
This dissertation only considers the signal ’ s distortion by interconnect, such as delay, reflection, discontinuity of microstrip, crosstalk and simultaneous switching noise, and so on . nowadays, there are some simulation software in pcb level, but they are lack of the well ability of modeling . in order to simulate the interconnect accurately, we have to make use of three-dimension full wave analysis method, whose disadvantage is low speed in computing, but is competent for developing rules in high-speed designs 目前也有一些針對這些噪聲的高速pcb板級仿真軟件,但它們都缺乏詳盡的建模能力,特別是當頻率逐漸提高和電路板日益復雜后,更是顯得無能為力,要精確地對互連結構進行分析,三維全波仿真器似乎不可缺少,其缺點就是速度慢,對整板仿真很難實現,但非常適用于規則開發,而這正好是本文除了建模與仿真方法研究外另一個重點。
First, the dissertation introduces transmission line theory, analyzes si in the design of high speed pcb, including reflection, crosstalk, simultaneous switch noise etc in detail . secondly, the dissertation simulates the reflection and crosstalk of the given circuit models using hyperlynx, the eda software of mentor corporation, and shows the waveforms of reducing reflection by adding terminators and the waveforms of the crosstalk influenced by changing the parameters of transmission lines . at last the dissertation summarizes the solutions to reducing reflection, crosstalk and ssn, and introduces the design flow of high speed pcb based on si 本文首先介紹了傳輸線理論,詳細分析了高速pcb設計中的信號完整性問題,包括反射、串?dāng)_、同步開關噪聲等,然后利用mentorgraphics公司的eda軟件hyperlynx對給定電路模型進行了反射、串?dāng)_仿真,并給出了通過端接技術減小反射的仿真波形和通過改變傳輸線參數對串?dāng)_的影響的仿真波形,最后總結了解決反射、串?dāng)_和同步開關噪聲的措施,并介紹了基于信號完整性分析的高速pcb板設計流程。
Analyzed the correlative theory of signal integrity such as reflection, crosstalk, simultaneous switch noise etc in detail, 2 . simulated reflection and crosstalk, gave the corresponding waveforms, and summarized the solutions to reducing reflection, crosstalk and ssn, 3 . using the method of signal integrity analysis, finished the pcb design of high speed data sampling system independently, 4 本文所完成的工作主要有以下幾個方面:1.對引起信號完整性問題的反射、串?dāng)_、ssn進行了較深入的理論分析;2.給出了在常見情況下解決信號完整性問題的一些方法,并進行了相應的仿真驗證;3.運用信號完整性分析方法,獨立完成了高速數據采集系統pcb板的設計制作;4.完成了系統ad部分的調試。